Earlex Heat Gun HG1200 User Manual

G136.qxd:G29 09/05.qxd 28/7/11 09:31 Page 1  
EARLEX HG1200  
Thank you for purchasing the Earlex heat gun.  
This is a highly versatile tool that can be used in a  
variety of applications.  
BEFORE USE - PLEASE READ THE SAFETY &  
OPERATING INSTRUCTIONS  
Please retain for future reference  
 
G136.qxd:G29 09/05.qxd 28/7/11 09:31 Page 3  
OPERATION  
Removing paint - general  
Before starting work it is advisable to test the  
work surface for the ideal temperature to  
use. The table below gives an indication of  
the likely heat settings required but always  
start with the low heat setting. All  
Do not heat the paint for too long as this  
will burn the paint, making it difficult to  
remove.  
1.Choose the required nozzle and fit  
onto the heat outlet.  
applications, with the exception of removing  
paint from window frames, can be performed  
without using a nozzle, however for best  
results nozzles are recommended.  
2.Hold the gun with nozzle approximately  
50mm (2”) from surface of paintwork.  
3.Starting with the low heat setting, move  
the gun slowly backwards and forwards  
until the paint blisters and bubbles.  
4.Immediately remove the paint with a  
scraper or shavehook.  
Suggested Ratings  
Low  
Welding plastic  
5.Aim to heat the paint just ahead of the  
scraper so that you can develop a  
continuous action.  
High  
Paint stripping  
Bending plastic  
Heat shrinking  
plastic  
Defrosting pipes  
Removing vinyl  
floor tiles  
Soldering  
Lighting BBQs  
Removing paint from window frames  
WARNING – Glass can break easily when  
heated.  
1.Use the glass protection nozzle.  
2.Ensure the nozzle is facing the correct  
way to deflect heat away from the  
glass before you switch on the heat  
gun.  
Nozzles  
3.Rotate the gun/nozzle 90º as you move  
to horizontal or vertical bead (take care  
it could be hot!).  
The gun is supplied with two different  
shaped nozzles, which can be used as  
follows:  
4.Paint can be removed by using a  
shavehook and/or a soft wire brush.  
Concentrator Nozzle - G84  
Maintenance  
G
Directs a  
Always allow the machine to cool down  
(before storing) and disconnect from the  
power supply. The heat gun should be  
cleaned before being stored away by wiping  
over with a clean damp cloth. DO NOT USE  
CHEMICALS. Ensure that the ventilation  
slots are not blocked.  
G84  
concentrated heat  
flow to the work  
surface.  
G
Ideal for removing  
paint in awkward  
corners, crevices,  
mouldings,  
beading or  
architraves.  
Trouble Shooting  
Concentrator nozzle  
If a problem occurs always switch off the  
unit immediately and disconnect from  
power supply.  
Glass Protection Nozzle - G89  
My unit fails to work?  
G
Deflects the heat  
G89  
If you are using an extension cable it must  
be fully unwound and rated at 15 amps  
capacity.  
away from glass  
or other fragile  
areas.  
Refer to ʻThermal cut outʼ on page 2.  
G
Ideal for window-  
Glass  
sills, ledges,  
protection nozzle  
frames and  
base boards.  
3
 
G136.qxd:G29 09/05.qxd 28/7/11 09:31 Page 4  
WARRANTY  
This product is guaranteed for a period of 24 months against faulty materials and workmanship. While  
every possible care is taken by Earlex to ensure that our products leave the factory in good working order,  
Earlex cannot under any circumstances accept liability for problems or damage caused by their  
subsequent use. It is the responsibility of the user to ensure that surfaces to be treated, cleaned or  
stripped are suitable for this product. This warranty does not affect your statutory rights. This warranty  
excludes the use for hire purposes. In the event of a fault occurring please contact our helpline before  
returning the unit to our Service Department at the address below together with a copy of your purchase  
receipt. All repairs will be dealt with promptly.  
IF YOU REQUIRE FURTHER ASSISTANCE PLEASE CONTACT OUR HELPLINE ON:  
Tel: 888-783-2612 email: [email protected]  
Earlex reserves the right to modify or improve this product without prior notice.  
Colors may vary from those shown.  
For information on other products in the Earlex range, please contact us at the address below or visit our  
Earlex Inc.  
8261 Highway 73, Suite F,  
Stanley, N.C. 28164, USA  
Earlex Inc, Toll Free 888-783-2612  
G136 07/11  
©Earlex Inc. 2011  
 

Cobra Electronics GPS Receiver SL3 User Manual
Cooper Lighting Indoor Furnishings VRM332 User Manual
Cooper Lighting Work Light 50W MR16 User Manual
Cornelius Beverage Dispenser Drop In and Free Standing Ice Cooled Dispensers User Manual
Craftsman Portable Generator 919679580 User Manual
Cypress Clock FS781 User Manual
Eclipse Fujitsu Ten GPS Receiver AVN 5500 User Manual
Everpure Water System CGS 10 10 User Manual
GE Monogram Oven ZET737BW User Manual
Generac Portable Generator 005031 2 User Manual